Examples of 'nut driver' in a sentence
Meaning of "nut driver"
This phrase refers to a hand tool used to tighten or loosen nuts and bolts. It typically consists of a handle and a socket-like attachment designed to fit the shape and size of different nuts. It is commonly used in mechanical work and DIY projects
How to use "nut driver" in a sentence
Basic
Advanced
nut driver
Carefully lift nut driver out of burner throat.
Reattach the tip with the nut driver.
Then use the nut driver to tighten or loosen.
Orifice spud must be captured in the nut driver.
Use a small socket or nut driver to go down through the.
Remove center hinge pin using hex nut driver.
Push the nut driver onto the chuck until it engages.
Socket wrench or nut driver driver.
The screw nut driver assembly has a screw nut driver.
Replace center hinge pin with hex nut driver.
The nut driver travels along a helical lead screw which is connected to the rotator.
Remove bottom hinge and shim using hex nut driver.
Inch wrench or nut driver if changing bracket to flush-mount configuration.
Remove top hinge and shim using hex nut driver.
A 1/4 socket wrench or nut driver may be required to tighten short screws.
See also
Install top hinge and shims on opposite side of cabinet using hex nut driver.
Tighten the nut against the ball using a 4mm nut driver and 1 Phillips screwdriver.
Using a s / le " nut driver or hex socket, remove the screw from the tensioner.
Loosen the top burner orifices using a 7 mm nut driver.
The screw nut driver assembly is adapted to automatically tighten a screw nut 301 to be tightened.
Apply masking tape to the end of a 7 mm nut driver to help.
Use a 4mm nut driver and 1 Phillips screwdriver to tighten the hardware.
Hand Tool only, Remove the spray tip with a nut driver.
Yeah, the nut driver.
Flat-blade screwdriver or 7 mm hex nut driver.
Use ¹ ⁄ ₄ " nut driver and previously removed screw to secure cover.
Use 6 mm socket and wrench or 6 mm nut driver to tighten.
Using a %6 " nut driver or hex socket, remove the screw from the tensioner.
Use 6 mm socket wrench or 6 mm nut driver to remove the.
Attach ignitor to nozzle adapter bracket with screw using a 1/4 " nut driver.
With a 5/le " nut driver or hex socket, remove the screw from the tensioner.
Secure the axle to the landing gear using a 7mm nut driver and 10mm box wrench.
Use a ¹ ⁄ ₄ " hex nut driver to turn both brake feet clockwise the same amount.
A second end 60 of the lever is to be adapted to pivotally engage a nut driver 62.
Fig . 5 is a schematic side view of a screw nut driver assembly 400 according to a typical embodiment.
Remove the 3 loose nuts on the terminal block using 3/8 " nut driver or socket.
Using a ¹ ⁄ ₄ " hex head socket, nut driver or Phillips screwdriver, remove terminal box cover.
The adjuster shaft 34 is inserted through the proximal end of the nut driver 33.
With radio system off, remove both rear wheels with 5.5mm nut driver.
Remove the three loose nuts on the terminal block using a 3/8 " nut driver or socket.
Hold freezer door in place while removing center hinge pin with a 5/16 " hex nut driver.
Tighten the hardware using a 2 Phillips screwdriver and 5.5mm nut driver.
You'll also be interested in:
Examples of using Nut
Show more
I am kind of a hard nut to crack in that department
A nut who knows a lot about bombs
Loosen the bottom nut to eliminate water
Examples of using Driver
Show more
They look to the driver as their father
Driver did not go down without a fight though
Check whether the driver is installed properly
