Examples of 'polymer sample' in a sentence
Meaning of "polymer sample"
polymer sample ~ refers to a small portion or specimen of a polymer material that is taken or used for testing, analysis, or experimentation. It is commonly used in scientific or industrial contexts for quality control, research, or product development purposes
How to use "polymer sample" in a sentence
Basic
Advanced
polymer sample
Place dish and popcorn polymer sample in a desiccator.
The polymer sample is then placed on the protruding pin.
Transfer the popcorn polymer sample into a petri dish.
In some cases isopropyl alcohol was also added to the polymer sample.
The polymer sample is not subjected to any particular treatment prior to analysis.
There is no specific treatment of the polymer sample before analysis.
The polymer sample is washed with deionized water and dried under vacuum at room temperature.
The organic portion of the polyester polymer sample is allowed to dissolve.
The thickness is measured by a sensor with no contact to the polymer sample.
This test is conducted by dissolving a polymer sample in xylene under reflux in a flask.
G is representative of the actual measured density in the respective polymer sample.
After transfer of the saturated polymer sample into a heating bath foaming occurs.
The analysis gives the molar mass spread of a polymer sample.
After the transfer of the saturated polymer sample into a heating bath foaming takes place.
Polydispersity reflects the distribution of individual molecular weights in a polymer sample.
See also
The plasma afterglow effectively sterilised the polymer sample and caused no noticeable thermal damage.
The capped sample tube is left at room temperature overnight to swell the polymer sample.
The test for XS comprises dissolving a polymer sample in xylene under reflux in a flask.
The stack was removed from the molder and disassembled to provide a monolithic polymer sample.
Each polymer sample had its cold flow resistance measured using a Scott tester.
All three wash solution tested show a good solubility efficiency of the fouling polymer sample used.
Mn weight of polymer sample in g / number of moles from end group analysis.
The functionality percentage may be determined from proton NMR measurements of a polymer sample.
The epoxy / polyester composite polymer sample was then subsequently comminuted.
The result is the weight % based on the polymer sample.
From the polymer sample a compression moulded 10 mm thick sheet has been prepared.
The method of claim 1, wherein the glucose polymer sample is a solution of icodextrin.
Dissolving the polymer sample in at least one solvent to form a polymer solution ;.
The polymer alone was separated and collected, and dried to give a polymer sample.
At this point the polymer sample degrades or oxidizes liberating additional heat ( exotherm reaction ).
The distilled water was added to the reactor first, followed by the polymer sample.
Figure 2 shows the bound styrene in polymer sample 1b prepared by the distributed feed method.
The relative amount of branching is determined using the g ′ - index of the branched polymer sample.
This procedure involves compression molding the polymer sample into film having a thickness of about 4 mils.
The results demonstrate the aTREF-rGPC apparatus is a powerful tool for the characterization of a polymer sample.
Figure 7 is a two dimensional color graphical representation of a polymer sample characterized by the aTREF-rGPC device.
The polymer sample temperature is plotted in Figure 6 versus the irradiation time.
In specific embodiments, the molecular weight distribution within the polymer sample is relatively low.
The solubilized of polymer sample is injected in a volume of 100 ul.
The solution was then kept still for 30 minutes and the precipitated polymer sample was collected.
Additional data for the polymer sample is included in Table 3.
The polymer sample was isolated, washed, and dried.
Preparation of the polymer, There is no specific treatment of the polymer sample before analysis.
A polymer sample is taken every 10 minutes at the reactor exit.
FIGURE 2 represents data obtained from scanning a film of a viscous polymer sample dried on a microscope slide.
The polymer sample ( 1 ) was estimated in the manner described before.
This blended product was designated polymer sample 15.
The solid polymer sample was dried in a vacuum oven for 12 hours.
The volume of the solution of the polymer sample injected is 50 ul.
The polymer sample contains about 1-2 ppm of the near infrared fluorophore.
You'll also be interested in:
Examples of using Polymer
Show more
Injected polymer compound shell in three sizes
We seem to be a bit light in the polymer sciences
High resistance polymer flow indicator cover
Examples of using Sample
Show more
Engineer training and sample terms of reference
Sample of sequence of targets for newspaper microfilming
Mfi particulate sample mass collected at mode i mg
