Examples of 'radial thickness' in a sentence
Meaning of "radial thickness"
radial thickness - This phrase is often employed in technical or scientific discussions to describe the measurement of thickness in a radial direction, typically in circular or symmetrical objects. It pertains to the dimension or extent from the center to the outer edge
How to use "radial thickness" in a sentence
Basic
Advanced
radial thickness
The radial thickness of the arms increases also.
It is noted that the casing may be said to have a certain radial thickness.
The radial thickness of each segment also is important.
The second bead may have a greater radial thickness than the first bead.
Radial thickness of the insulation.
A simple annular collar may be of constant internal and external diameter and constant radial thickness.
Radial thickness to burn.
After expansion the radial thickness is at least equal to 1 mm.
The sleeve has a height 1 and a radial thickness e.
It also enables the radial thickness of the ribs to be kept to a minimum.
In the ground portions wire 7 has a smaller radial thickness.
The radial thickness of the insulation shall be appropriate to the diameter of the conductor.
In an operative, implanted condition, the regions of the cuff have differing radial thickness.
The radial thickness of the sidewall increases in thickness in a direction away from the base.
Advantageously, the tubular brace has a radial thickness less than that of the sleeves.
See also
The radial thickness of each region as a percentage of the CFC radius varies.
The long leg 23 has a length approximately equal to the radial thickness of said coils.
The partition may have a radial thickness smaller than the radial thickness of the branches.
The expansion applies a prestress by the reduction of the radial thickness of the elastic sleeve 3.
The maximum radial thickness of each segment 2 is a few millimeters.
Figure 3 shows a graph visualising the pressure dependency of a typical applicable radial thickness of the lip.
Again advantageously, the radial thickness of each lever arm decreases rearwards.
This contact height 81 may also be termed the radial thickness.
Its greatest radial thickness approximately corresponds to the thickness of the sheathing 8.
Furthermore, the weakening region can have the smallest radial thickness of the extruded profile body.
The radial thickness of the insulation must be at least 25 mm.
Likewise, satisfactory results have been obtained with a radial thickness E of less than 2 mm.
Annular spaces having a radial thickness of about 3 mm will generally give satisfactory results.
The wall / rim member 58 may if desired be of minimal radial thickness.
Denotes the radial thickness of the 2 magnets ;.
The magnetic element 73 is in the form of a plate with a slight radial thickness.
The radial thickness of the insulation shall be at least 25 mm.
Thus, relative dimensions of an axial length L and radial thickness RT have a predetermined range.
The radial thickness of the toothed front end portion is set to 0.5 mm.
They may be integrated into the radial thickness of the annular platforms 28.
The radial thickness of the lip 23 is adapted to the intended pressure interval.
Dimensions of the blanks were 6mm axial thickness and 6mm radial thickness.
In other words, the radial thickness of ring gear 23 is not constant.
The component may also have defects in its radial thickness ( not shown ).
Moreover, it is the radial thickness of each rear arm 76 that decreases rearwards.
Thus, when the underlayer is made of polytetrafluoroethylene, its radial thickness should be about 25 micrometers.
The radial thickness ( ER ) of a tape layer is given by the following equation, EPMATHMARKEREP.
Thus, the circumference CE 1 has an annular and frustoconical shape, with a non-zero radial thickness.
For example, this radial thickness E is less than 1 mm.
Radial thickness of the first non - mm =.
Before machining, the hub as a radial thickness T1.
The radial thickness I of the magnets is on the order of 2.5 millimeters.
Guide compartment 42 is made in the radial thickness of middle part 14.
Radial thickness of the second non - mm =.
The cavity 38 is formed in the radial thickness of the spacing part 32.
You'll also be interested in:
Examples of using Radial
Show more
Note where the radial artery was severed
Radial and ulnar arteries were both severed
I am checking for radial keratotomy scars as we speak
Examples of using Thickness
Show more
Minimum recommended thickness of zinc vs thickness of steel
Thickness of tanks made with double walls
Reduction of wall thickness and additional protection
