Examples of 'speed of the rotor' in a sentence
Meaning of "speed of the rotor"
This phrase refers to the rate at which the rotor of a machine or device rotates. It is commonly used in the context of machinery or equipment that relies on a rotating component, such as turbines, engines, or fans. The speed of the rotor is measured in rotations per minute (RPM) or angular velocity
How to use "speed of the rotor" in a sentence
Basic
Advanced
speed of the rotor
Electrical angular speed of the rotor.
The speed of the rotor is slightly less than the synchronous speed.
Rotational speed of the rotor.
The frequency of the flash varies with the speed of the rotor.
Furthermore the rotational speed of the rotor may possible be lowered.
The frequency of the flashing changes with the speed of the rotor.
This allows the rotational speed of the rotor to also be reduced.
The output frequency of the transmitter is proportional to the speed of the rotor.
Information about the rotating speed of the rotor is being sent to the VarioStress.
This waiting time varies as a function of the rotational speed of the rotor.
Speed of the rotor of an induction motor is always less than its synchronous speed.
The other factor is the operating speed of the rotor.
The rotational speed of the rotor of the generator 18 is typically significantly higher.
Let us consider now the calculation of the rotational speed of the rotor.
The precession further increases the speed of the rotor to an ordinary operational speed.
See also
Torque and power in a generator are related by the rotation speed of the rotor.
Suitable parameters also include speed of the rotor and pitch angle of the rotor blades.
The maximum forward speed may be dictated by a maximum speed of the rotor blades.
The instantaneous speed of the rotor is measured ;.
The taper time depends on the taper angle and the rotational speed of the rotor.
Determining said position and / or speed of the rotor from said induced voltage ;.
This operation suppresses an excessive rise of the rotational speed of the rotor 1a.
The speed of the rotor is controlled according to instructions stored in the microprocessor 's memory.
Back EMF is proportional to the speed of the rotor.
So, the speed of the rotor also varies.
Therefore, the upper limit of the revolution speed of the rotor 2 can be increased.
The speed of the rotor in the microcooker apparatus is held constant at about 5200 rpm.
Denotes the ratio of the rotation speed of the rotor to the base speed ;.
Furthermore, the controller 36 may comprise a control unit for controlling the speed of the rotor 4.
Thus, the position and the speed of the rotor can be determined in real time.
Such control parameter may e.g. be generated power and operating speed of the rotor.
WR = peripheral speed of the rotor.
First, the pilot opens the throttle completely to increase the speed of the rotor.
The rotational speed of the rotor blades is 125 rpm.
Alternatively, the operating parameter EV is the speed of the rotor.
The tip speed of the rotor is preferably set at between about 15 and about 25 m / sec.
The first regulating loop can alter the rotation speed of the rotor of the generator 26.
Consequently, the rotor 10 rotates at a speed greater than the critical speed of the rotor 10.
The oil lubrication allows for a higher rotational speed of the rotor 3 than the grease lubrication.
The actual speed Nact may then be controlled to a desired speed of the rotor 4.
W r, the rotation speed of the rotor.
The load torque may also be adjusted to control the speed of the rotor 38.
Variation of the rotation speed of the rotor 24.
A numerical value from 500 RPM up to the maximum speed of the rotor can be.
Vector 45 is the tangential speed of the rotor.
A number value from 200 rpm to the maximum speed of the rotor can be set.
The three hall ICs 94 detect the rotation angle and rotation speed of the rotor 66.
The three Hall ICs 94 detect a phase angle and a rotating speed of the rotor 66.
The sensor 11 V senses the rotational speed of the rotor 2.
The vector U 1 = wR corresponds to the rotational speed of the rotor blades 22.
You'll also be interested in:
Examples of using Rotor
Show more
The rotor is blocked or the differential pressure
Set the tail rotor trim to centre
The rotor blades are made of laminated rubber
Examples of using Speed
Show more
The speed of the vacuum source shall be
I must have hit speed dial by mistake
Zoom speed is determined by the amount of rotation
