Examples of 'tensile strengths' in a sentence
Meaning of "tensile strengths"
Tensile strengths: The maximum stress a material can withstand while being stretched or pulled before breaking or deforming permanently, often used to quantify the durability or elasticity of materials in engineering, construction, or manufacturing processes
Show more definitions
- plural of tensile strength
How to use "tensile strengths" in a sentence
Basic
Advanced
tensile strengths
Best tensile strengths even at high temperature.
Diameter with corresponding tolerances and tensile strengths.
Web tensile strengths were tested as described below.
There are no significant differences between the tensile strengths.
Two different tensile strengths available.
I have written a blog on the varying tensile strengths.
Also tensile strengths and compactibilities were evaluated.
All the samples displayed acceptable tensile strengths.
Transverse tensile strengths are not stated.
Fibers and fabric hydrophobicity as well as tensile strengths were good.
High tensile strengths at break are desirable.
The test is used to determine the residual tensile strengths.
Tensile strengths were measured in accordance with the aforedescribed procedure.
Polyester polyurethanes show higher tensile strengths than polyether polyurethanes.
The tensile strengths of the unconditioned and conditioned samples are determined.
See also
They additionally exhibit low tensile strengths particularly in wet environments.
Films prepared from the compositions have exceptional tensile strengths.
The transverse tensile strengths are not stated in the examples.
The binder formulations were evaluated in the following examples for their tensile strengths.
A standard tensile strengths apparatus was mounted with two flat plates.
All three polyurethanes had moderate tensile strengths and elongations.
Tensile strengths of these alloys are also significantly higher than the commercial alloys.
Ive written a blog on the varying tensile strengths of different natural fibres.
The tensile strengths compacted samples are typically tested before and after being conditioned.
I have written a blog on the varying tensile strengths of different natural fibres.
The tensile strengths were measured after substantial completion of coagulation of the collagen casing.
Nets having this structure have good tensile strengths in all directions.
The diametral tensile strengths were measured following the same procedure as described earlier.
The sample is then pulled and the tensile strengths of the sample recorded.
This reduces the sand binder recoating requirements and improves tensile strengths.
They have greater tensile strengths and improved capacities to absorb water.
The resulting oriented filaments have good straight and knot tensile strengths.
The in vivo tensile strengths shown below are averages of the abdominal and muscular values.
Small increases in selenium content resulted in large increases in impact and tensile strengths.
The tensile strengths of the towels saturated with water were measured in the cross direction.
Concrete and ceramics typically have much higher compressive strengths than tensile strengths.
The tensile strengths are measured both in the machine direction and the cross machine direction.
The thermosets are useful as plaster replacements because of their high impact and tensile strengths.
The greatest tensile strengths were reached in some cases when the wettest slab was coated.
In both cases steel wires or steel cords with higher tensile strengths have been tried.
The following tensile strengths and Frazier permeabilities were obtained.
The analyzed properties are the compressive and the tensile strengths and the elastic modulus.
Tensile Strengths are similar as is shrinkage for each degree of treatment.
The inventive films all have very good puncture resistance and good tensile strengths.
Tensile strengths of the present alloys may vary depending upon Mg content.
The resulting blend was ductile and had high impact and tensile strengths and tensile elongation.
The tensile strengths are significantly higher for the PA and MPA systems.
The blends according to the present invention provide molding plastics having unexpectedly high tensile strengths.
The average dry and wet tensile strengths are reported in Table III.
The TDT is the arithmetic total of the MD and CD tensile strengths.
You'll also be interested in:
Examples of using Tensile
Show more
Mechanical tensile test prehoistable navigation lights
The main advantages of the tensile test are
Tensile test on parent material of the bottom
Examples of using Strengths
Show more
Analysis of strengths and weaknesses of the response
These organizations have their own strengths
Identify individual strengths and highlight them
