Examples of 'turn the adjustment' in a sentence
Meaning of "turn the adjustment"
This phrase refers to the act of manipulating or changing a control or setting to modify or optimize a particular aspect or function of a device or system
How to use "turn the adjustment" in a sentence
Basic
Advanced
turn the adjustment
Turn the adjustment screw of the thermostat.
This will make it easier to turn the adjustment screw.
Turn the adjustment screw to the correct setting.
Level the deck by using a wrench to turn the adjustment.
Turn the adjustment cap and use as a tool.
To move the cutting bar away from the blades turn the adjustment screw counterclockwise.
Turn the adjustment knob for cutting depth.
To select a setting, turn the adjustment collar on the tool.
Turn the adjustment dial clockwise until it stops.
Use a small flat-blade screwdriver to turn the adjustment.
Turn the adjustment screw r to adjust the walking foot.
Should less pressure be required, simply turn the adjustment knob counterclockwise.
Turn the adjustment screw until the flame reaches.
If nails are driving too deep, turn the adjustment knob to the shallow side.
Turn the adjustment ring to the desired length setting.
See also
Use a small flat-blade screwdriver to turn the adjustment screw clockwise until tight.
Turn the adjustment nut counterclockwise as indicated by the arrow.
To seat the screw higher in the workpiece, turn the adjustment collar to the left.
Turn the adjustment wheel to the desired number of hours.
To seat the screw deeper in the workpiece, turn the adjustment collar to the right.
Turn the adjustment nut to lengthen or shorten the cable.
Cutting position to cut through light material completely . u Turn the adjustment knob counter-clockwise half a turn.
Turn the adjustment screws on the front of the pilot valves.
To adjust the axle, you will need a 19mm wrench to turn the adjustment nut.
Turn the adjustment rings on both sides to focus on a distant object.
Grasp the top part of the appliance and turn the adjustment button ( 2 ) a half-turn anti clockwise.
Turn the adjustment lever and set the deflector to throw.
Loosen the lock nut and turn the adjustment bolt counterclockwise Figure 43.
Turn the adjustment knob for faster or slower acceleration and braking.
Press memory key 4 and turn the adjustment knob until indicator M5 lights.
Turn the adjustment nut to the right to tighten the brake pedals.
To adjust the height turn the adjustment knob 5-6 full turns.
Turn the adjustment nut to the left to loosen the brake pedals.
To increase the cutting height, turn the adjustment lever towards the " + " mark.
Turn the adjustment screw until the flame reaches the desired size.
To select a digit in the current readout [ 6 ] and turn the adjustment knob to fine-tune.
Then turn the adjustment screw to raise the burn chamber as much as required.
To select a digit in the voltage readout [ 7 ] and turn the adjustment knob to fine-tune.
Turn the adjustment lock counterclockwise to decrease and clockwise to increase the volume.
Grasp the top part of the appliance and turn the adjustment button ( 2 ) a half-turn.
Turn the adjustment knob to adjust tracking and test until it rolls straight.
To adjust the axle you will need a 3/4 " wrench to turn the adjustment nut F.
Turn the adjustment screw anticlockwise until the rubber pad touches the fl oor.
To increase drag, turn the adjustment knob towards a higher graduation.
Turn the adjustment screw clockwise to increase the pressure or counterclockwise to decrease the pressure.
To decrease drag, turn the adjustment knob towards a lower graduation.
Turn the adjustment knob for the amplification till the best reception is set correctly.
To select a setting, turn the adjustment collar in the direction indicated on the tool.
Turn the adjustment screw until the flame is appropriate for a LOW setting.
Using a 7/16 " open-end wrench, turn the adjustment fastener to the desired position and retighten the fasteners.
You'll also be interested in:
Examples of using Turn
Show more
Persuade him to turn over a new leaf
Now turn around and meet him
The unit does not turn on when installed
Examples of using Adjustment
Show more
Adjustment for accrued income from investments
The single flow adjustment knob allows
Adjustment for other accruals and liabilities
