Examples of 'unscrew the screw' in a sentence
Meaning of "unscrew the screw"
unscrew the screw - means to remove a screw by turning it in the opposite direction to the one used to tighten it. It involves loosening the screw in order to separate or release something.
How to use "unscrew the screw" in a sentence
Basic
Advanced
unscrew the screw
Unscrew the screw on the lever to do this.
Use a screwdriver to unscrew the screw that closes lamp compartment of.
Unscrew the screw on the other side.
Remove the solution tank and unscrew the screw holding the green cover.
Unscrew the screw in the air regulating sleeve.
Use a Phillips screwdriver to unscrew the screw on the back and separate the.
Unscrew the screw and remove the door.
All I did was unscrew the screw.
Unscrew the screw to loosen it but do not remove it.
Remove the front cover ; unscrew the screw in the battery compartment.
Unscrew the screw of the cover by.
Put the BENNING CM 9 face down and unscrew the screw of the battery.
Unscrew the screw and remove the battery cover.
To do this, remove the adjustment knob and unscrew the screw by approx . 2 turns.
Unscrew the screw which holds the heating element.
See also
Cleaning or replacing accent lighting - Unscrew the screw 5 mm 4 mm Allen key.
Unscrew the screw and remove the door stopper c.
The longitudinal stop along the sanding belt . - To sand sloping surfaces, unscrew the screw.
Unscrew the screw from the battery compartment cover.
With the aid of the combination wrench 23, unscrew the screw from the mandrel 13.
Do not fully unscrew the screw to prevent it from falling.
If you want to use the tap ( E ), then unscrew the screw topS.
Unscrew the screw that closes the lamp compartment of the.
To install the batteries, unscrew the screw on the battery compartment on the back panel.
Unscrew the screw in the bottom which is to hold the steel.
Do not unscrew the screw completely!
Unscrew the screw top in a clockwise direction from the carafe.
On the Inline Oiler ( 5 ), unscrew the screw fixing to access the oil reservoir.
Unscrew the screw cap at the lower end of the microphone.
F Using a screwdriver, unscrew the screw 2 ( Figure E ) of the adjustment lock from Position 1.
Unscrew the screw clockwise or counter clockwise to extend or shorten the wire.
Completely unscrew the screw 6 and take off the sanding plate 5.
Unscrew the screw and remove the glass from the control panels.
If necessary, unscrew the screw and remove the side brush ( 8 ) from the body for more.
Unscrew the screw in the casing and take off the casing shell.
Unscrew the screw of the cover by turning it anticlockwise and remove the lid.
Unscrew the screw on the battery cover and remove the battery cover.
Unscrew the screw in the protective cover and remove the protective cover.
Unscrew the screw in the round ballcrank and take the round ballcrank out.
Unscrew the screw clamp enough to fit the clamp around the metal post.
Unscrew the screw on the microfilter cover and remove the cover Note.
Unscrew the screw A until you can move the handle.
Unscrew the screw and remove the door stopper 4.
Unscrew the screw ( K ) at the point of pressure measurement and connect the manometers.
Unscrew the screw that closes the lamp compartment of the fixture see “ A ” on the picture.
Unscrew the screw B in direction of arrow 2 and remove the wheel.
Unscrew the screw fixing the cover of the air filter Fig . L.
Unscrew the screw A next to the socket 1 on the bottom of the trimmer.
Unscrew the screw 15 completely with a screwdriver.
Next, unscrew the screw that 's pre-installed onto the molly bolt until it 's completely out.
You'll also be interested in:
Examples of using Screw
Show more
Tighten the screw through the clips
Screw the two sections of pole together
Remove the screw on the rear coupler
Examples of using Unscrew
Show more
Unscrew the bulb cover by turning anticlockwise
You can now unscrew the screws
Unscrew old filter by turning the filter to
