Examples of 'voltages and currents' in a sentence
Meaning of "voltages and currents"
voltages and currents: This phrase refers to the flow of electrical energy in a circuit, with voltages representing electrical potential difference and currents indicating the rate of flow of electric charge
How to use "voltages and currents" in a sentence
Basic
Advanced
voltages and currents
Working around high voltages and currents.
These voltages and currents have multiple causes.
Laboratory measurements of the transient voltages and currents.
Voltages and currents in the circuit.
Measuring high voltages and currents.
Voltages and currents were.
Transformers can vary the voltages and currents.
The voltages and currents are then calculated for this base case.
Apparatus for amplifying direct current voltages and currents.
Calculation of resistor voltages and currents will be identical to the previous solution.
Conventional and unconventional measurements of high voltages and currents.
This allows the three phase voltages and currents to be in time phase.
The relay prevents patient exposure to the calibration voltages and currents.
The axis voltages and currents then undergo a reference frame transformation.
The parameters shown in the display refer to internally measured voltages and currents.
See also
Voltages and currents within the capability of this test equipment can be hazardous.
On the rear of the plugin units the voltages and currents required should be indicated.
The interconnection of circuit elements imposes some restrictions on relationship between voltages and currents.
They model physical phenomena with electrical voltages and currents as the analog quantities.
The voltages and currents from series and parallel combinations of the batteries can be examined.
Analysis of a circuit consists of solving for the voltages and currents present in the circuit.
Input voltages and currents are sampled for calculation of the corresponding RMS values.
Selected complementarity of the voltage variations greatly reduces common mode voltages and currents.
Electrical unbalance Check voltages and currents of all three lines.
Power supplies exist called universal power supplies which propose several electric supply voltages and currents.
In this case, the circuit voltages and currents are independent of time.
Systems using straight DC voltage typically operate under high voltages and currents.
Circuits, voltages and currents in time and frequency domain, frequency characteristics.
Therefore the processor calculates the RMS values of the voltages and currents detected.
In a multi-machine system the voltages and currents of the stator in all the machines.
The Harmonic Analyzer allows observation and analysis of the harmonic components in voltages and currents.
For such frequencies, the concepts of voltages and currents are no longer used.
In addition, the electroplating reaction could be performed under a wide variety of voltages and currents.
For polyphase meter, the test voltages and currents shall be balanced polyphase.
Electrical and dielectric testing with DC and AC voltages and currents.
For polyphase meters, the applied voltages and currents shall be polyphase and balanced.
Three-phase input power is a product of three sinusoidal voltages and currents.
In a zero sequence network, resultant voltages and currents remain near the original input values.
This pick-up may also be used indirectly in the measurement of voltages and currents.
FIG . 3 shows an actual representation of the voltages and currents in the power distribution system.
The two-port equations impose a set of linear constraints between its port voltages and currents.
Under dry conditions induced voltages and currents occur on the cable as shown in Figure 2.
The nodes of the signal-flow graph will include both voltages and currents.
WARNING! Measuring high voltages and currents poses a life hazard.
The voltages and currents shall for practical purposes be balanced, i . e.
Monitoring VBUS and VCONN voltages and currents.
The voltages and currents are defined by their amplitudes ( peak values, not RMS values ).
Figures 5-8 trajectories of voltages and currents for different loads.
Moreover, it provides the following outputs, Pe, Qe in the form of voltages and currents.
Fig . 2 shows time diagrams of voltages and currents in this power supply circuit ;.
You'll also be interested in:
Examples of using Currents
Show more
The currents must have washed it away
Prevention of unfavourable currents and flow conditions
Other currents or configurations may be supplied on request
Examples of using Voltages
Show more
Higher voltages will damage the transmitter
Operate the compressor at voltages specifi ed on their
These voltages pose electrical shock hazards
