Examples of 'cap screw' in a sentence
Meaning of "cap screw"
cap screw - a type of screw with a cap or head designed for fastening objects together, commonly used in construction and machinery
Show more definitions
- A screw that is threaded along the entire length of the shaft and has a cap which is intended to rest against the side of the outermost material being screwed together when the screw has been screwed in to its maximum extent.
How to use "cap screw" in a sentence
Basic
Advanced
cap screw
Store the cap screw in a safe place.
Check torque of blade retaining cap screw.
Inner socket head cap screw for handle fixing.
Check the torque of the blade cap screw.
Remove the socket cap screw from the side ejector.
Hexagonal socket head cap screw.
Low head socket cap screw first adjustment notch shown.
Square socket head cap screw.
Start cap screw into thread just enough to hold blades in place.
One black cap screw.
Secure the pushrod guide with a socket head cap screw.
Insert rear cap screw into shear housing but do not completely tighten.
Percentage of hot bearings equipped with cap screw seal rings source.
Remove the cap screw located between the bladder and reservoir handle.
Be careful not to lose rear spacer bushing when removing middle cap screw.
See also
Then tighten the handle cap screw so that the cap and handle fit flush.
The setting tool can therefore set immediately on the prefitted cap screw.
Replace the socket cap screw securing with Loctite.
Tighten the ratchet lock lever and both hexagon socket head cap screw.
Loosen the socket head cap screw and open blade clamp with the wrench provided Fig.
Set the thermostat to the desired room temperature with a screw driver and replace cap screw.
Screw the new lock nut onto the hex head cap screw and tighten securely.
Place the release cam bushing and the release handle over the hex head cap screw.
To remove the plug, complete unscrew the cap screw and pull the plug upwards.
Firmly hold spring housing against head so it remains engaged with the 4mm cap screw.
Duplex bolts manufacturer hex cap screw and nuts - Winrock.
The differential adjustment device 37 may comprise one or more adjustment nuts and a cap screw.
Loosen, but do not remove, the hex cap screw on the left deck hanger bracket.
Secure in place with the socket head cap screw I.
Cap screw 21 is externally threaded and comprises a hexagonal socket 23 which allows to fasten the screw.
Repeat process for second Cap screw.
Tighten adjusting cap screw ( B ) to take slack out of belt.
Install o-ring and sediment cup with cap screw.
The cap screw 44 is used to adjust the cracking pressure of the ball valve 38.
Also known as an Allen screw or Allen bolt, or simply a cap screw.
Use a screwdriver to remove the valve cap screw ( Item 15 ), located at the end.
If tool rest post begins to slip, tighten up the hex socket cap screw E.
Tighten the cap screw ( Item 28 ) to the torque indicated in Table 1 using a torque wrench.
Remove and discard the low head socket cap screw Figure 4.
Turn the cap screw ( Reference B ) clockwise until a 1/4 inch belt deflection is noticed between the pulleys.
Re-install the low head socket cap screw.
While referring to page 137, replace the rotary hook RP and the cap screw.
Hub for cone bushing 18 Cap screw.
The shaft of the compression screw 24 transverses the hollow cap screw 21.
Attach the other side of the support leg with a M8 x 20 mm cap screw and M8 lock nut.
Left encoder housing half is attached to transmission plate 330 ( see Figure 7 ) using a cap screw.
The threaded recess 100 is positioned on the lower end of the healing cap screw 94.
In the embodiment shown, the outer race 60 is keyed against rotation with the cap screw 52.
