Examples of 'flathead screwdriver' in a sentence
Meaning of "flathead screwdriver"
flathead screwdriver ~ a type of screwdriver that has a flat, wedge-shaped tip that fits into the slots of a flathead screw
How to use "flathead screwdriver" in a sentence
Basic
Advanced
flathead screwdriver
Use a coin or flathead screwdriver to adjust the dials.
You can repair this with a flathead screwdriver.
We recommend a flathead screwdriver be used to tighten the screws.
Install requires only a flathead screwdriver.
Requires a flathead screwdriver for adjustments.
Remove the top hinge cover by using a flathead screwdriver.
Use the flathead screwdriver to remove the clips.
Pry it off with a flathead screwdriver.
Place a flathead screwdriver in the cleaning deck inlet plug.
Pop it out with a flathead screwdriver.
Insert a flathead screwdriver between the bracket and mounting spring.
I had seen someone tried to jimmy with a flathead screwdriver.
We recommend using a flathead screwdriver to lift and remove them.
Remove the motor shaft end cover by prying with flathead screwdriver.
You may need to use a flathead screwdriver to remove them.
See also
Use a flathead screwdriver to turn the screw in the counterclockwise or clockwise direction.
And this is a flathead screwdriver.
Use a flathead screwdriver to remove four mylars from the hinge cover.
Remove the cover with a clothwrapped flathead screwdriver to the cover.
Use small flathead screwdriver or pliers to carefully pry off pinion from motor.
Adjust the screw in the valve hole using the flathead screwdriver.
Need a flathead screwdriver.
Remove the cap on the interior surface of the liftgate with a flathead screwdriver.
But he was quicker with a flathead screwdriver than most people with a key.
Locate the two calibration ports on the front and side of tool with a flathead screwdriver.
Wrap a flathead screwdriver or similar tool with a soft cloth to prevent damage to the clip.
It may be helpful to use a spudger or small flathead screwdriver for extra leverage.
Insert a small flathead screwdriver into the crack and press the battery out.
That have collected in the blade guide with a flathead screwdriver or similar implement.
Twist the flathead screwdriver in the direction of the arrow and remove the cover.
Remove the hubcap from the single side wheel using the flathead screwdriver and set aside.
You can also use a large flathead screwdriver to be sure the adaptor is seated correctly.
Press the tab outward and remove the battery slowly and carefully using a small flathead screwdriver.
Insert a flathead screwdriver between the mounting bracket pin and the mounting bracket.
Separate the bottom cap from the handle with a small flathead screwdriver Fig.
Use a small flathead screwdriver to carefully pry the safety cover out of the smokestack.
Adjust the screw in each valve hole using the flathead screwdriver C.
Insert a small flathead screwdriver into the slot and gently pry open the transmitter.
But I can go on the fact that I had to borrow a flathead screwdriver from Nora.
Use a coin or flathead screwdriver to loosen the screw fastening the cover completely Q.
Using a soft cloth-wrapped flathead screwdriver.
Flathead screwdriver and mallet to remove knock-out.
That I had to borrow a flathead screwdriver from nora.
If the flathead screwdriver contacts the terminal, a short circuit may occur.
To adjust the switch, use a flathead screwdriver if needed.
Insert a flathead screwdriver into the slot in the bolt, as shown.
Tool required, phillips or flathead screwdriver.
All you need is a flathead screwdriver and about 15 minutes to get them installed.
Replacement tool required, flathead screwdriver.
It is like a normal flathead screwdriver except it 's got two vampire-like teeth on the end.
You'll also be interested in:
Examples of using Screwdriver
Show more
Use a screwdriver to loosen the air shutter
Always take away the screwdriver or similars
Use a screwdriver to secure all wiring connections
Examples of using Flathead
Show more
Use flathead screws on the access hatches
Hand me the biggest flathead you got
We recommend a flathead screwdriver be used to tighten the screws
