Examples of 'idler pulley' in a sentence
Meaning of "idler pulley"
idler pulley: A mechanical component used in machinery and vehicles to guide and maintain tension in belts, chains, or other flexible components without transmitting power
How to use "idler pulley" in a sentence
Basic
Advanced
idler pulley
Belt must be in groove on top of idler pulley.
Check if idler pulley jammed or stuck.
Place backside of belt around idler pulley.
Idler pulley with integrated bearings.
The arm is adapted to support an idler pulley.
Remove reverse idler pulley from idler arm.
Releasing belt tension with the idler pulley.
Pivot the idler pulley toward the right.
The hubload transducer fits within an idler pulley.
Place the idler pulley into the window as shown.
Release the idler bracket so that the idler pulley tightens.
A fixed idler pulley must operate over a range of temperature conditions.
The pulleys may comprise a drive pulley and an idler pulley.
What is needed is a fan idler pulley configured to receive a ball bearing.
Place the belt to the inside of the other flat idler pulley.
See also
The idler pulley on the arm is then placed against the belt.
Slightly loosen the hex bolt next to the flat idler pulley.
Pull the cable around the idler pulley and toward the trolley.
The idler pulley is then attached to the outer race of the ball bearing.
Pumps are automatically connected to the idler pulley when the deposit is full.
Move the idler pulley rod to the lower hole in the idler bracket.
One of the pulleys is a drive pulley while the other pulley is an idler pulley.
Remove the belt from the idler pulley by working it under the belt keepers.
Route the belt around the drive pulley and under the idler pulley.
Ensure belt is routed correctly around idler pulley and seated properly in engine pulley groove.
Remove the cotter pin and spring washer from the idler pulley rod.
You may have to move idler pulley more than once to obtain the correct tension.
Route the backside of the belt around the fixed idler pulley of the deck.
Remove the belt from the reverse idler pulley and then from around the transmission pulley.
Figure 4a is a detail of the slideably mounted idler pulley.
Remove the idler pulley bolt and move the belt from under the idler pulley keeper.
Now you're going to install the idler pulley.
Ensure idler pulley W is located on the outside of belt as shown.
Replacing the belt, idler pulley or drum motor.
The tension of the belts is adjusted with an idler pulley 3.
I'm replacing the idler pulley for the drive belt.
Belt tension is main - tained by use of a spring loaded idler pulley.
Retighten the left idler pulley hex nut loosened in step 3.
The hubload transducer is used with a non-torque transmitting idler pulley.
In such case, the idler pulley is installed on the tensioner pivot arm.
Make sure the motion drive belt is installed correctly on the idler pulley 2.
The idler pulley as in any preceding claim, wherein the bearing is self lubricating.
The effective diameter and the contact diameter of the idler pulley 8 are thereby decreased.
Remove the idler pulley bracket by removing the hex screw, flat and lock washers.
Remove the deck belt from around all pulleys, including the deck idler pulley.
Therefore the idler pulley must have a different pitch than the drive pulley ( different geometry ).
You can probably blame a maladjusted or misaligned belt, but do not ignore the idler pulley.
Timing belt idler pulley - Quality Supplier from China.
The double pulley 23 then acts as an idler pulley.
The pulley 84 is an idler pulley and is not described further.
You'll also be interested in:
Examples of using Idler
Show more
Pulley and idler not in correct adjustment
Belt must be in groove on top of idler pulley
Remove idler plates from scrub head
Examples of using Pulley
Show more
Rotate the pulley to be sure it spins freely
Check for a damaged belt or damaged pulley
Pulley and idler not in correct adjustment
