Examples of 'mm screws' in a sentence
Meaning of "mm screws"
MM screws are small hardware components that are typically used in construction or manufacturing, with 'MM' representing the diameter measurement in millimeters
How to use "mm screws" in a sentence
Basic
Advanced
mm screws
Remove the three 5 mm screws from the muffler protector.
X3 mm screws Place lower duct covers using one plastic bracket at each side 4 needed.
Position the bracket plate and secure it with Ø 3 mm screws not supplied.
Remove the two 4 mm screws that were hidden under the cover.
Open the phone and remove the four stickers that hide the four 0.5 mm screws.
Remove the three 4 mm screws from the exhaust deflector, and remove the deflector.
If necessary, attach the belt clip using the two supplied M3 x 8 mm screws.
Remove the two 4 mm screws from the muffler deflector, and remove the muffler deflector.
The screws are preferably flathead 8x80 mm screws with ribs under the screw head.
Remove the six 5 mm screws from the muffler protector, and remove the muffler protector.
Attach the belt clip using the supplied M3 x 8 mm screws.
Remove the four 5 mm screws from the muffler protector and remove the muffler protector.
Secure the appliance in the recess using 4 x 14 mm screws.
Remove the three 4 mm screws from the exhaust deflector, and remove the deflector applicable types.
Attach the wing to the fuselage with six 3 x 16 mm screws.
See also
Use the provided 76 mm screws to attach the support to the wall.
Attach vent cover bracket to wall flush to the ceiling using 2 - 5 x 45 mm screws.
Insert three 3 x 16 mm screws through the vertical tail and into the fuselage.
Assemble the 3 pieces of the vent cover bracket using 4 - 4 x 8 mm screws provided.
X 9.5 mm screws used for supporting the lower chimney located inside canopy behind filters.
Connect glass mantle to range hood with the 2 glass mounting brackets and 4 - 4 x 8 mm screws.
Use the provided 10 x 38 mm screws and washers to secure these brackets in place.
Install the glass retainer brackets to the range hood with the four 4.2 x 8 mm screws.
Install the 10 x 59 mm screws through the mounting holes on the back plate.
The flatter spacers are simply fastened together with the magnet using two 2.2 x 16 mm screws.
Insert 2 - 5 x 35 mm screws at the upper screw locations, but do not completely tighten them.
Attach the vent cover ceiling bracket to the deflector with the two 3.5 x 9.5 mm screws provided.
Install four 4.2x19 mm screws into the round mounting plate openings and tighten all mounting screws.
L The housing can be further fastened to the cabinet with the four 2,9 x 16 mm screws.
Do not insert blue TriLock Ø 2.5 mm screws into the pre - angled plate holes!
Secure the other end to the wall with ST4 x 20 mm screws DD.
Use a 0 Phillips screwdriver to remove the eight 3.25 mm screws uncapped from the previous step.
Method Fix the base to the heater pole using the 3 pcs M8 * 25 mm screws provided.
Fasten the hood to the wall with 2 5x45 mm screws ABSOLUTELY NECESSARY.
Make final adjustments using the M10 x 45 mm screws attached to the joints.
Attach the ground wire on the post with M4x12 mm screws and an M4 washer.
Use the Torx T5 screwdriver to remove the four 5.4 mm screws from the upper inner face.
Proximal bone fixation is achieved by means of 3.5 mm screws Figure 8 - A and B.
You'll also be interested in:
Examples of using Mm
Show more
Mm vinyl coated steel retracting security cable
Is the nominal diameter of the rim expressed in mm
Mm small brush with black polyester bristles
Examples of using Screws
Show more
The screws are provided in the literature pack
Fully tighten screws with hex wrench
Screws are visible on the burner control panel
