Examples of 'torx screws' in a sentence
Meaning of "torx screws"
torx screws: a type of screw head characterized by a six-point star-shaped pattern, requiring a compatible screwdriver for tightening or loosening
How to use "torx screws" in a sentence
Basic
Advanced
torx screws
Remove the two torx screws from the lamp assembly.
The latch can be repositioned vertically by adjusting the two torx screws.
Remove the two torx screws from the top of the belt cover.
The battery is held in place by a few Torx screws.
Remove the slotted Torx screws to separate the.
Secure the handle with the slotted Torx screws.
The two Torx screws are required later for securing the mounting bracket.
Mount the cover plate and tighten the Torx screws.
Remove the three Torx screws from the center left side of the cabinet.
The rail mounted launcher is held in with three Torx screws.
Remove the two Torx screws that hold the top hinge to the cabinet.
Remove the center hinge bracket by removing the three Torx screws.
Remove the slotted Torx screws to separate the handle from the handle support.
Fasten the bracket to the computer housing using the Torx screws supplied.
Will test Torx screws as well.
See also
Release the suction pipe socket by unscrewing the four combination Torx screws.
DO NOT remove the torx screws from the rail assemblies.
Fasten the brackets to the computer housing using the existing Torx screws.
Remove the 6 Torx screws on the back cover.
Place the cover panel over the wall support panel and secure with Torx screws provided.
Four Torx screws secure the luminaire glass firmly so that it is burglar-proof.
Unscrew the four combination Torx screws.
T2 Torx screws secure the display assembly to the the rest of the phone body.
Remove the three Torx screws.
Unscrew 3 Torx screws on the left and right at the case and on the bottom 5.
Torx Plus drivers will not fit into standard Torx screws.
With a Torxdriver, remove the 2 Torx screws that hold the top hinge to the cabinet.
The Retina display comes out after removing a few Torx screws.
Remove the door trim by loosening the 2 Torx screws attaching it to the range.
Remove the tape covering the round holes to reveal two T5 Torx screws.
Secure the handle with the slotted Torx screws using a T25 Torx driver or flat blade screwdriver.
Lock the housing cover with 4 torx screws.
Unscrew 3 Torx screws on the left and right at the housing and on the bottom 5.
Stick the tape down against the new clips and reinstall the two T5 Torx screws.
Edit Once removed, there are 2 torx screws holding the circuit board in place.
Torx screws ensure that you can ( dis ) assemble Bloom as much as you 'd like.
Now reinstall the front cover and secure using the 3 M3x8 Torx screws.
Remove the following T10 Torx screws securing the hard drive brackets to the iMac,.
Adjust the two camber tube clamps ( C ) to the required height and replace the 4 Torx screws.
Remove the two silver T6 6 mm Torx screws from the left side of the hard drive.
Using a torx T6 screwdriver remove the six 15 mm torx screws.
Remove the 4 Torx screws from the Front.
Remove the 4 torx screws ( T20 ) and slide out the coil and drain pan assembly.
Remove the four 9.0 mm silver T10 Torx screws from the sides of the power supply.
Undo the Torx screws ( Torx T10 ) and remove the protective cap.
Remove five 5.1 mm T10 Torx screws from around the outer perimeter of the fan assembly.
Remove the four Torx screws ( 12 ) from the base plate and take off the.
Remove the two 3.3 mm T5 Torx screws securing the AirPort / Bluetooth card to the logic board.
You'll also be interested in:
Examples of using Screws
Show more
The screws are provided in the literature pack
Fully tighten screws with hex wrench
Screws are visible on the burner control panel
Examples of using Torx
Show more
Torx bolt can not be ordered individually
And with the torx screwdriver
Torx screwdriver and screws are provided
