Examples of 'rudder servo' in a sentence
Meaning of "rudder servo"
rudder servo: a component of a control system in vehicles, aircraft, or boats that is responsible for operating the rudder. This phrase is commonly used in engineering and transportation contexts
How to use "rudder servo" in a sentence
Basic
Advanced
rudder servo
Position the rudder servo in the fuselage.
Center the rudder and rudder servo.
Center the rudder servo using the radio system.
The nosewheel is steered by the rudder servo.
The box holding the rudder servo controller was unsealed.
Guide the cable to toward the rudder servo.
The rudder servo is the center servo in the servo tray.
Use the radio system to center the rudder servo.
The rudder and rudder servo should also be centered at this time.
Connect the linkage clevis to the rudder servo arm.
The rudder servo arm can be removed to attach the ball ends.
Disconnect the steering clevis from the rudder servo arm.
Attach the servo arm to the rudder servo perpendicular to the servo centerline.
Adjustments to the rudder cable will be made at the rudder servo.
Attach the elevator and rudder servo connectors to the appropriate channels of the receiver.
See also
Install the grommets and brass eyelets in the rudder servo.
Make sure the rudder and rudder servo remain centered while tensioning the cables.
Place the elevator servo just behind the rudder servo.
Rudder servo goes to the Rudder channel.
Attach the two remaining clevises to the rudder servo arm.
Connect the rudder servo connector to the extension in the fuselage labeled RUDD.
Assemble the connection to connect the cable to the rudder servo.
RuDDer anD ruDDer SerVo inStaLLation.
Install the grommets and brass eyelets into the rudder servo.
Rudder servo and pull-pull cable installation.
Guide the pushrod through the hole in the pushrod on the rudder servo.
Elevator servo, rudder servo and receiver installation.
Thread a servo mounting screw into each of the holes in the rudder servo mounting holes.
The rudder servo will use a double-sided servo arm.
The fin also carried a large and prominently balanced rudder with a rudder servo surface on outriggers.
With the rudder servo centered, fi t the servo arm to the servo.
Center the tail wheel, rudder and rudder servo.
Set the rudder servo and nosewheel to neutral by screwing the clevis 72 in or out.
In addition, the antirotation lug was separating from the rudder servo.
The motor, speed controller and rudder servo could then be ruined by overloading.
Attach the ends of the cables to the heavy-duty rudder servo arm.
Set the rudder servo to centre, using the procedure outlined for the winch.
Connect the linkage clevis ( behind the battery compartment ) to the rudder servo arm.
With the rudder servo centered, lightly pull the cables rearward near the rudder.
The model 's aerobatic repertoire can be expanded by installing the optional rudder servo and linkage.
Glue the rudder servo in the fuselage using UHU-por, positioning the output arm in the.
Assemble the ends for the pull-pull cables to connect the rudder to the rudder servo.
The main rudder servo motors were completely unserviceable, and the turbo-dynamos were severely shaken.
Repeat with the second pull-cable, then route both cables forward to the rudder servo.
Plug the rudder servo and additional Y-harness into this.
Attach the Z-bend in the pushrod to the rudder servo horn.
The box holding the rudder servo controller was unsealed . The mechanism was altered.
Re-attach the arm to the rudder servo.
Glue the rudder servo and the canopy latch catches 22 in place.
The next step is to assemble the servo mount for the rudder servo part 26.
You'll also be interested in:
Examples of using Rudder
Show more
Rudder and starboard diving planes disabled
Center the rudder and rudder servo
Rudder control via rotating handle with
Examples of using Servo
Show more
Woofer servo for reduced woofer distortion
Run your full servo and arming
Servo mode partial light output settings
