Examples of 'tensile tester' in a sentence
Meaning of "tensile tester"
A tensile tester is a scientific instrument used to measure the tensile strength and other mechanical properties of materials. It applies controlled forces to a sample and measures the resulting deformation or breaking point. Tensile testers are commonly used in engineering, material science, and quality control to evaluate the strength and performance characteristics of various materials
How to use "tensile tester" in a sentence
Basic
Advanced
tensile tester
The intervening forces are recorded by a tensile tester.
Start the tensile tester and data collection.
This test was conducted using a tensile tester.
The tensile tester was prepared as follows.
The samples are pulled on a tensile tester in a shear mode.
The tensile tester is calibrated according to the apparatus instructions.
Start the tensile tester.
The tensile tester is calibrated according to the apparatus instruction.
The samples are then tested individually on the tensile tester.
The tensile tester was used in determining the peel force.
The samples were then tested individually on the tensile tester.
Start the tensile tester as described in the tensile tester instrument manual.
The skin sections were measured for tension on a tensile tester.
The tensile tester is then activated so that its crosshead moves downward.
Then attach the sample into the tensile tester.
See also
The jaws of the tensile tester are moved apart in the prescribed manner.
It was attached to the load cell of the tensile tester on the crosshead.
The tensile tester was activated to cause the suture to be torn from the graft.
The samples can then be tested individually on the tensile tester.
Tensile tester capable of obtaining a peak load and equipped with an appropriate load cell.
Dry tensiles were measured by breaking the handsheets in a tensile tester.
An Instron tensile tester was used to determine tensile properties.
The unbonded ends of the paper and film are clamped in a tensile tester.
The assembly was then tested with an MTS tensile tester to determine tensile shear strength.
The tab was then placed in the upper jaw of the tensile tester.
Set the Tensile Tester to run a Compression test.
The sample was clamped in the bottom jaws of the tensile tester first.
An Instron Tensile Tester is used for the test.
The strength of the test piece was then measured using a tensile tester.
The tensile tester calculates the stretch at Peak Load and the stretch at Failure Load.
The test panel is placed in the lower grip of the tensile tester.
The tensile tester consisted of two jaws spaced 3 in apart.
The strip ends were clamped in the bottom jaw of a conventional tensile tester.
The test condition for the tensile tester are set as follows,.
One of the eight strips is placed between the grips of the tensile tester.
Thereafter, the samples were mounted on a tensile tester to determine their peeling strength.
One of the three strips is placed between the grips of the tensile tester.
Figure 6 schematically shows a tensile tester for establishing the crushing strength of a tablet.
The tensile parameters of the crimps were then measured with the tensile tester.
Basically, the tensile tester calculates the stretches vía the formulae described above.
Tensile strength of the membrane was also determined by the tensile tester described above.
After the tensile tester has been zeroed, the friction body is placed on the platform.
The bond strength was measured using an Instron tensile tester.
In the tensile test, a tensile tester made by Instron corporation was used.
Tenacity is typically measured on a tensile testing machines such as a Instron tensile tester.
The longitudinal compliance was measured on an Instron Tensile Tester using pneumatic grips as follows.
Table VII sets forth the cohesive force values as measured on the Instron Tensile Tester.
Procedure, The tensile tester is calibrated according to the apparatus instructions and set to zero.
The hook material is clamped into the lower jaw of the INSTRON tensile tester.
Tensile tester setting Place the samples between the clamps, placing them symmetrically to the clamps.
You'll also be interested in:
Examples of using Tensile
Show more
Mechanical tensile test prehoistable navigation lights
The main advantages of the tensile test are
Tensile test on parent material of the bottom
Examples of using Tester
Show more
Connect the tester to the junction to measure
Range selection is performed automatically by the tester
Do not expose the tester to rain or snow
