Examples of 'thickness of the sheet' in a sentence
Meaning of "thickness of the sheet"
A phrase referring to the measurement of the width or depth of a single layer of material, such as paper or metal
How to use "thickness of the sheet" in a sentence
Basic
Advanced
thickness of the sheet
This insulation is proportional to the thickness of the sheet.
The thickness of the sheet metal components does not have to be specifically adjusted.
This speed depends on the thickness of the sheet.
The thickness of the sheet stock may vary depending upon application.
It is thus typically five times the thickness of the sheet.
The thickness of the sheet for stretching as obtained above is not critical.
The temperature varies with the thickness of the sheet.
Throughout the thickness of the sheet or strip if the carrier is in this form.
Depth greater than or equal to half the thickness of the sheet.
The thickness of the sheet material may be greater than that of the structure.
Bending usually do not generate change in the thickness of the sheet metal.
The thickness of the sheet is substantially constant at any point of the output portion.
The final thickness of the disk is determined by the thickness of the sheet.
The thickness of the sheet is roughly dependent on the thickness of the ceramic layer.
Score it to a depth about half way through the thickness of the sheet.
See also
The thickness of the sheet remains practically constant and we obtain a very good surface.
The stamping operation may change the thickness of the sheet metal.
The thickness of the sheet then ensures its stiffness and therefore its function.
The sheet material includes one or more notches based on a thickness of the sheet material.
The metering nip reduces the thickness of the sheet to the approximate final thickness.
The corner piece has a thickness which approximately corresponds to the thickness of the sheet components.
The thickness of the sheet was about 5 mm.
Db ath blec schnitt blech Sheet thickness Defines the thickness of the sheet metal.
In an embodiment, the thickness of the sheet material is determined by successive rollers.
Preferably, their imprint results in little change in thickness of the sheet.
For example, half of the thickness of the sheet is removed locally.
The thickness of the sheet of wood 31 corresponds to the smallest thickness of the matches.
The thickness e of the slot is substantially equivalent to twice the thickness of the sheet 6.
Represents the thickness of the sheet or of the workpiece near the bend ;.
The weight the sheets / layers of aluminium used depends on the thickness of the sheet.
In this case, the thickness of the sheet gives to the strip its mechanical characteristics.
The Z-dimension usually corresponds to the thickness of the sheet.
The thickness of the sheet in its initial state is also called pre-molding thickness.
Those data are for example the thickness of the sheet metal, its width, its hardness.
The thickness of the sheet in its final state is also called post-molding thickness.
The width of the slot 38 is twice the thickness of the sheet metal, for example.
The thickness of the sheet 24 is dependent upon the application and the finished product thickness.
The magnitude d1 provides a measure of the thickness of the sheet document S1.
The S9 sees the thickness of the sheet above and below the screen decrease further.
Depth of openings 5 equal to approximately 80 % of the total thickness of the sheet.
The thickness of the sheet measured 90 microns.
According to one embodiment the material thickness of the sheet metal is 0.5-1 mm.
The thickness of the sheet is about 1 mm.
Typically the slots 4 are around 0.01mm wider than the thickness of the sheet.
The thickness of the sheet should be about 11 gauge.
A round opening 26 is cut in the thickness of the sheet in the connection section 25.
The thickness of the sheet is preferably in the range 1 to 4 mm.
The film thickness of the sheet was set at 400 µm.
The thickness of the sheet 10 is of the order of a few hundreds of um.
The thickness of the sheet was then reduced by 70 % by cold rolling.
You'll also be interested in:
Examples of using Thickness
Show more
Minimum recommended thickness of zinc vs thickness of steel
Thickness of tanks made with double walls
Reduction of wall thickness and additional protection
Examples of using Sheet
Show more
Polycarbonate sheet to protect against direct contacts
We got all type of potential on this sheet
Model information sheet for local communities
