Examples of 'thickness of the metal' in a sentence
Meaning of "thickness of the metal"
refers to the measurement of the width or depth of a piece of metal, indicating its physical dimensions. It is often used in construction, fabrication, or manufacturing industries to specify the strength, durability, or suitability of a metal component for a particular purpose
How to use "thickness of the metal" in a sentence
Basic
Advanced
thickness of the metal
This doubles the thickness of the metal.
The thickness of the metal panels is limited.
Here is a flaw which extends through the thickness of the metal.
The thickness of the metal layers is not so critical.
It is therefore necessary to limit the thickness of the metal layer to a strict minimum.
The thickness of the metal coating also affects conductivity.
The interference colour depends on the thickness of the metal oxide layer.
The thickness of the metal plating is selected so as to give a catalytic surface.
Other solutions to reduce locally the thickness of the metal sheet can be envisioned.
The layer thickness of the metal in the runner can also be estimated theoretically.
This thickness is thus necessarily identical to the thickness of the metal starting blank.
Indicates the thickness of the metal sheet composing the stator teeth.
The roughness of the central zone increases with the thickness of the metal grid.
The thickness of the metal base can be adjusted depending on the desired rejection level.
This decision should be based on the thickness of the metal that you typically cut.
See also
The thickness of the metal plating is generally about 1 um or a few microns.
The ultrasonic measuring system measures the thickness of the metal coating over the seam.
Does the thickness of the metal sheets have any effect?
Other variables were kept constant, including the thickness of the metal layer.
The thickness of the metal oxide layer can be as thin as about 1 nm.
Required equivalent wall thickness of the metal to be used, in mm.
The thickness of the metal layer 23 is sufficient for this layer to be totally reflective.
Increasing the thickness of the metal layer ;.
A thickness of the metal plate is a matter of design choice, and can be appropriately set.
In the following discussion, the thickness of the metal primer layer is as deposited.
The thickness of the metal deposit does not spoil the flexibility of the backing sheet 2.
From time to time re-measure the thickness of the metal of the work piece support.
The thickness of the metal shield around the Faraday box is not of much concern, either.
The width W 1 of the pins and therefore the thickness of the metal layers deposited ;.
However, the thickness of the metal oxide coating plays an important role.
A preferred distance is at least 10 times the thickness of the metal sheet 1b.
In view of the small thickness of the metal strips, laser welding is particularly appropriate.
The depth of the groove lies between 1 and 20 times the thickness of the metal strip ;.
The thickness of the metal layers must be smaller than that of layer 20.
E1 the required equivalent thickness of the metal to be used in N/mm2.
The thickness of the metal film is in particular comprised between 50 nanometers and 10 micrometers.
Where, e1 required equivalent wall thickness of the metal to be used ( in mm ) ;.
The total thickness of the metal and dielectric layers in this example is about 9.5 mm.
Therefore, it was possible to reduce the thickness of the metal blank by 5 to 10 %.
The thickness of the metal plate will be, for example, of the order of 5 millimeters.
The desired overall thickness of the metal coating is shown in phantom at 456b.
The thickness of the metal film 6 coating the glass disc 5 is also crucial.
After deformation, the thickness of the metal wall 4 may optionally be constant.
The thickness of the metal layers is preferably 4 to 50 nm.
Furthermore, the thickness of the metal plate is 20 inches.
The thickness of the metal layer was approximately 0.07 micron.
For example, the thickness of the metal dots is less than or equal to 500 nm.
Thickness of the metal in which the ladder is etched 0.1 mm ; and.
For one embodiment, the thickness of the metal coating is comprised between 10 nanometers and 100 micrometers.
Thickness of the metal plate and depth of the slotted waveguide, 100 microns.
You'll also be interested in:
Examples of using Metal
Show more
But there is metal in the electrolyte regulators
It sounds like a wheelchair going down a metal staircase
Plastic or metal foil vent is not recommended
Examples of using Thickness
Show more
Minimum recommended thickness of zinc vs thickness of steel
Thickness of tanks made with double walls
Reduction of wall thickness and additional protection
