Examples of 'tighten nuts' in a sentence
Meaning of "tighten nuts"
The phrase 'tighten nuts' is used in the context of fastening or securing nuts, typically in mechanical or construction settings. It refers to the act of using tools, such as wrenches or spanners, to tighten the screws or bolts on nuts, ensuring a secure and firm connection. Tightening nuts properly is important for maintaining structural integrity and preventing mechanical failures
How to use "tighten nuts" in a sentence
Basic
Advanced
tighten nuts
Tighten nuts by hand to prevent cross threading.
Only finger tighten nuts at this time.
Tighten nuts until handle feels secure.
Use of blue threadlock to tighten nuts is advisable.
Tighten nuts to lock leveling foot in place.
Replace the outlet tube and tighten nuts.
Always tighten nuts in the top position.
Replace filter in proper position and tighten nuts.
Do not tighten nuts until the washer is leveled.
Tighten downrod set screws and then tighten nuts.
Tighten nuts using the sequence shown at right.
Slide bolts through locating holes and tighten nuts.
Tighten nuts to secure the blower to the hood.
Mount other clamp jaws and also tighten nuts.
Tighten nuts and bolts on both sides of spreader at locations shown.
See also
Install pneumatic line and tighten nuts to the appropriate torque.
Tighten nuts and bolts only to the recommended tightening torques.
Tighten set screws and then tighten nuts on the set screws.
Do not tighten nuts any further than to the angle as listed.
Reinstall the washer and lock nuts and tighten nuts securely.
Tighten nuts to secure top of blower and use sheet metal.
Align the wheels parallel to the carrier tubing and tighten nuts securly.
Tighten nuts so that internal wheel rim adjoins hub exactly.
After all screws are inserted, tighten nuts firmly.
Tighten nuts but do NOT overtighten.
Re-tighten set screws in motor housing yoke and then tighten nuts.
Lower rotary rake, tighten nuts according to recommended torque and given sequence.
Mount the first clamp jaw as close as possible to thimble and tighten nuts 4.
Place wheel on hub, tighten nuts so that wheel rim adjoins hub exactly.
Attach second clip as close to loop as possible . Tighten nuts but not firmly.
Place wheel on hub, tighten nuts so that wheel rim tightly fits the hub.
Horizontal flow, Insert flange bolts through bottom flange bore and tighten nuts.
When the concrete has dried, tighten nuts to keep the pump firmly in position.
Tighten nuts and bolts from Step 1.
If the setting will not hold, tighten nuts E to increase friction on speed control levers.
Fit the screws and nuts ( see illustration ), do not tighten nuts for the moment.
Lower the manure spreader, tighten nuts according to recommended torque and given sequence.
Tighten downrod ( A ) set screws and then tighten nuts.
Always tighten nuts and bolts well, especially the fastening bolts for the blades.
Repeat steps 2 and 3 for opposite side, then tighten nuts with adjustable wrench.
Now tighten nuts firmly, as shown in figure B.
Repeat Steps 4 and 5 on the opposite end of the reel then tighten nuts M.
Wrench tighten nuts and bolts from step 1 and 2.
Repeat Steps 4 and 5 on the opposite end of the reel then tighten nuts D.
Fully tighten nuts on M8 carriage bolts.
Once the wheels have been correctly aligned, tighten nuts 8.1.
While holding screw 15 tighten nuts 14 to lock the comb in place.
Tighten nuts ( K ) and recheck each end.
After repositioning the brush head, tighten nuts securely to approximately 236 inch-lbs.
Tighten nuts (G) and recheck each end.
You'll also be interested in:
Examples of using Nuts
Show more
Soak nuts and seeds before blending
Tighten the small nuts with a spanner
Place nuts in recessed areas on front of handle
Examples of using Tighten
Show more
Tighten the screw through the clips
I will just tighten these up for you
Tighten properly the connection block screws
