Examples of 'tighten nut' in a sentence
Meaning of "tighten nut"
tighten nut - It refers to the action of securing or fastening a nut by turning it in a clockwise direction to reduce play or looseness
How to use "tighten nut" in a sentence
Basic
Advanced
tighten nut
Tighten nut by hand to avoid cross threading.
Replace the outlet tube and tighten nut.
Tighten nut to secure slide mechanism to track.
Insert wire through hole and tighten nut.
Tighten nut securely with a wrench.
Hold wheel with a rag and tighten nut counterclockwise.
Tighten nut firmly with fingers.
Securely tighten nut when done.
Tighten nut to hold adjustment in place.
Insert tube into valve fully and tighten nut.
Tighten nut of the rear grille on the shaft.
Hold screw in place with a screwdriver and tighten nut.
Tighten nut onto water valve with adjustable wrench.
Insert wand end over nozzle and tighten nut.
Then tighten nut securely to threaded part of axle bolt.
See also
Engage spindle lock pin and tighten nut with wrench.
Tighten nut after blade is tracking in the center of the wheel.
Engage spindle lock button and tighten nut with wrench.
Be sure to tighten nut until spring coils touch each other.
Replace axle sleeve washer and nut and tighten nut.
Only tighten nut sufficiently to drive the wheel without slippage.
Attach upholstery tab to bolt and tighten nut and bolt assembly.
Tighten nut while turning the wheel until a slight drag is felt.
Insert tube into the union fitting on the unit and tighten nut to union.
Tighten nut counterclockwise against the blade while holding the locking rod.
Slide the EMI cover back and tighten nut.
Tighten nut A on either side of the swing arm.
Place the new bit in collet II and tighten nut III completely.
Nut Tighten nut to these threads.
Open the endshield and tighten nut A.
Always tighten nut B when finished the operation of tightened.
After this adjustment is made, tighten nut.
Tighten nut by hand, additional tightening should not be necessary.
Hold whisk in place and tighten nut anticlockwise using open ended wrench size 8.
Tighten nut firmly with fingers . or AmbiSpanner - do not use pliers or other tools.
Insert the heart bolt, tighten nut firmly and secure with a safety ring.
Tighten nut (E) against the adjuster then recheck the setting on both side of the reel.
After achieving required tightness, tighten nut 4.
With wrench, tighten nut 2 turns past finger tight.
Lock the gear shaft and tighten nut 8.
Tighten nut ( 6 ) so that the guide wheel can be turned on the guide trolley.
Block shaft and tighten nut 8.
Tighten nut snugly using an adjustable wrench, see Figure 6.
Once setting is complete hold screw ( C ) firmly and tighten nut D.
Tighten nut counterclockwise against the blade while holding the locking rod Fig . 10.
Place the washer ( JJ ) and nut ( KK ) on cord wrap screw and finger tighten nut.
Also tighten nut “ A ” if it was necessary to loosen.
Place one wrench on fitting body ( D ), and tighten nut ( E ) with other wrench to torque shown.
Tighten nut ( D ) to lock adjustment in place.
This all part put in to the base tube P11, set requied height and tighten nut P9.
You'll also be interested in:
Examples of using Nut
Show more
I am kind of a hard nut to crack in that department
A nut who knows a lot about bombs
Loosen the bottom nut to eliminate water
Examples of using Tighten
Show more
Tighten the screw through the clips
I will just tighten these up for you
Tighten properly the connection block screws
