Examples of 'annealing time' in a sentence
Meaning of "annealing time"
Annealing time refers to the duration during which a material is heated to a certain temperature and then allowed to cool slowly. It is commonly used in the context of metallurgy and material science to improve the properties of the material through controlled heating and cooling processes
How to use "annealing time" in a sentence
Basic
Advanced
annealing time
Annealing time as a function of temperature for various sheet thicknesses.
Further studies on the effects of annealing time and implantation temperature have been performed.
The annealing time and temperature can be adjusted based upon the composition employed.
The protection ring voltage is determined at the first order by the annealing time duration.
The affect of annealing time on stearic acid removal was examined as follows.
There are two reasons for the use of a long annealing time in the amplification reaction.
The annealing time varies between one hour and five hours.
Resulting photoluminescence characteristics can be dependent upon an annealing temperature and an annealing time period.
Adjusting the annealing time enables more restricted but more controllable variations.
The material and dimensions can also be determinative of the annealing time and temperature.
The final annealing time is selected to insure complete removal of the rolling lubricants.
For this, we diverted the NCs coalescence during the annealing time.
Other formulas expressing the annealing time may be established for the other nanostructurations.
Annealing time can be at least 1 minute to several weeks long.
Generally, the higher the annealing temperature, the shorter the annealing time.
See also
Excessive annealing time or temperature leads to undue grain growth and poor bend formability.
However, the duration of the heat treatment is generally shorter than the annealing time.
Therefore, the annealing time is limited as described above.
Figure 4 illustrates the change in the FT-IR spectra with the lapse of annealing time.
The annealing time necessary to obtain a given degree of homogenisation is expressed by, a2.
Depending on the selected temperature the annealing time may vary between 5 minutes and a few hours.
If the annealing time is too short, no sufficient getter and passivation effects are obtainable.
The particles equilibrated to a steady particle size after at least 8 hours of annealing time Figs.
Therefore, the annealing time must be long enough to obtain complete phase separation.
For example, the B phase is generally reduced with increasing annealing time.
Typically, the annealing time exceeds one hour, and is preferably two hours o r more.
The results are summarized in the following Table, TABLE 1 Annealing medium Annealing time.
The annealing time was kept constant at 24 hours.
Similarly, contraction of an Mo-Si bilayer increases with the annealing time.
Preferably the annealing time is of more than 30 hours.
Figure 11 shows the water uptake as function of annealing time.
Therefore the annealing time should be limited to 5 seconds to 20 hours.
Note an annealing speed of 1m/min corresponds to a short annealing time of about 6 seconds.
The total annealing time to obtain the compensated silicon is 4.5 hours.
The annealing speed was 2m/min which corresponds to an annealing time of about 6 sec.
The annealing time is typically from about 1 second to about 1 min.
The thicker the layer 4, the longer the annealing time and / or the higher the annealing temperature.
The annealing time durations are identical ( one hour and four hours ).
However, in other embodiments, the annealing time may be as long as 24 h.
Although the annealing time is not particularly defined, it is preferably 30 minutes to 4 hours.
Accordingly, it is preferable that a range of the annealing time is 30 seconds to 30 minutes.
Annealing time varies depending on the annealing temperature, but is preferably about 1 minute to 1 hour.
The results shown in Fig . 4 reflect an annealing time of 30 minutes.
The annealing time may be between 30 minutes and 2 hours.
The measurements are performed at 150 ° C., after an annealing time of 5 min at the measurement temperature.
The annealing time for this temperature range is 30 to 45 minutes.
FIGS . 5A, 5B and 5C show the evolution of the microstructure over the annealing time.
Most preferably the annealing time varies within a range of 2 to 4 hours.
In addition, a preferable annealing time of the hot-rolled steel sheet annealing is 1 to 300 seconds.
You'll also be interested in:
Examples of using Time
Show more
Spent a lot of time with the ladies
Time and tide wait for no man
A woman needs time to think things over
Examples of using Annealing
Show more
Spare parts for annealing furnace pressing
Annealing of flat glass and of container glass
The surface is flattened by annealing at high temperatures
