Examples of 'blade screw' in a sentence
Meaning of "blade screw"
A blade screw is a type of screw that has a blade-like shape instead of a traditional threaded design. It is often used in applications where quick assembly or disassembly is required, as the blade-shaped section allows for easy insertion and removal using a specialized tool
How to use "blade screw" in a sentence
Basic
Advanced
blade screw
Tighten blade screw securely by turning counterclockwise.
Repeat for each blade screw.
Remove blade screw by turning it counterclockwise with.
Depress spindle lock button and replace blade screw.
Tighten blade screw securely by turning it clockwise with.
Have an authorised workshop tighten the cutting blade screw.
Tighten the blade screw again.
Install the outer clamp washer and blade screw.
Make sure the blade screw is tight and secure.
Locks the saw blade to tighten or loosen the blade screw.
The thread of the blade screw is right hand clockwise.
Press down the spindle lock lever and loosen the blade screw.
Slide the tip of a flat blade screw driver between the.
Tighten blade screw securely by turning it clockwise with the blade wrench.
Loosen the blade by turning the blade screw clockwise.
See also
Install the blade screw into blade adapter and crankshaft.
Remove the cover with a flat blade screw driver as shown.
With a flat blade screw driver until the arrow is pointed at.
Use the hex key to tighten the blade screw securely.
Be sure the blade screw is tight to prevent slipping or loosening during operation.
Depress spindle lock button and remove blade screw and outer blade washer.
Check the cutting blade screw and have an authorised workshop tighten it if necessary.
The spindle lock allows you to secure the blade when turning the blade screw.
Insert and securely tighten the blade screw counterclockwise with the wrench.
Make sure blade screw and handle retaining nuts are tightened securely before operating.
Loosen the blade by turning the blade screw counter clockwise with a coin.
Tighten the blade screw by turning it counterclockwise while depressing engaging the spindle lock.
The spindleqock button allows you to secure the blade when turning the blade screw.
Use a thin blade screw driver to turn the screw located in the brass shaft.
Depress spindle lock button, then replace blade screw.
Use a small flat blade screw driver and insert it into the slot located.
Use the wrench to loosen and remove the left-hand thread blade screw clockwise.
Gently twist the flat blade screw driver to loosen the glass lens cover.
Blade screw loose Have damaged parts replaced by excessively an authorised workshop.
When replacing the blade, the blade screw should also be replaced.
Washers for blade screws can be set on each blade screw prior to installing blades.
With the spindle-lock button firmly depressed, turn the blade screw clockwise to loosen it.
It will prevent the blade screw from properly securing the blade on the spindle.
Press down the spindle lock lever while tightening the blade screw ( clockwise ) with wrench provided.
Grass bag Clean Blade screw tightness and blade condition Check.
Position your saw as shown in Figure 4, depress spindle lock button, and remove blade screw.
Remove blade screw by turning counter-clockwise.
Place 1 lock washer and 1 flat washer ( in that order ) on a blade screw.
Install the blade screw and, engaging the spindle.
Install the blade, outer flange, washer, spring washer and blade screw Fig . 1.
Using a small flat blade screw driver, pry up on center console trim panel.
Install the blade screw and, engaging the spindle lock, tighten the screw firmly with.
After tightening the upper blade screw ( A ), tighten the setting screw with the pin provided.
Tighten blade screw securely by turning it counterclockwise with the hex “ T ” wrench.
NOTE, Turn blade screw clockwise to remove it.
