Examples of 'adjusting ring' in a sentence
Meaning of "adjusting ring"
adjusting ring: A small metal or plastic ring that is used to modify or regulate the size or fit of a piece of equipment or machinery
How to use "adjusting ring" in a sentence
Basic
Advanced
adjusting ring
The adjusting ring can be aligned in any.
Pull down the adjusting ring.
Adjusting ring volume press the menu key.
Release it so that the adjusting ring.
Rotate the adjusting ring to the desired setting.
The sleeve is longitudinally guided in the adjusting ring.
The adjusting ring can be placed at any position.
Then tighten the screws to secure the adjusting ring.
Adjusting ring for torque setting.
The fastening torque may be adjusted by turning the adjusting ring.
The adjusting ring and the full lift.
Do not operate the tool with the adjusting ring set.
The adjusting ring does not lock when the pointer is.
Switch to hammer drilling by turning the adjusting ring in position of hammer drilling.
The adjusting ring does not lock when the arrow is.
See also
Always tighten the two screws to secure the adjusting ring after adjusting the fastening torque.
The adjusting ring should be turned only within the.
Counterclockwise rotation e Number r Adjusting ring t Red mark y Screw.
Adjust the adjusting ring to the proper torque level.
Verify the torque position of the Torque Adjusting Ring.
Set the clutch adjusting ring to the drill position.
Preferably, the movable insert section comprises a movable adjusting ring.
Adjusting ring can be placed at any position because it does not work.
Steering heaviness of blades or of adjusting ring lead to increase power consumption of actuator.
The adjusting ring therefore does not have as simple a form as is desirable.
Set the router-depth adjusting ring to the zero position.
The adjusting ring may be rigidly secured to the outlet nipple.
As discussed above, the means of adjusting ring thickness can vary.
Turn the adjusting ring so that the arrow points to the marking.
To adjust it, loosen the two screws and turn the adjusting ring.
The adjusting ring should be turned only within the numbered range.
Consequently, rotation of the adjusting ring opens and closes the chuck jaws.
Adjusting Ring Grip the middle of the handle.
You can find the Torque Adjusting Ring between the Chuck and the drill body.
Adjusting ring for the picture sharpness 9.
Align the number 1 on the adjusting ring with the pointer on the gear housing.
Take out the inner tube for desired height and screw the height adjusting ring 14.
Adjust the adjusting ring to the proper torque level for your work.
Work range of clutch auto-stop Increments on adjusting ring for fastening torque.
Regulate the torque adjusting ring to a higher position to reach the best result.
After obtaining the desired preload, turn counter-ring E until it stops against adjusting ring f.
Release it so that the adjusting ring rotates and becomes visible in the hole.
Control switch with lockbutton Forward / reverse pushbutton Depth gauge adjusting ring.
Release it so that the adjusting ring rotates and the hole becomes visible as illustrated.
Control switch with lockbutton Forward / reverse pushbutton Torque adjusting ring Depth gauge adjusting ring.
Set the clutch adjusting ring to the proper position and set the speed to low.
The fastening torque can be adjusted in 17 steps by turning the adjusting ring.
Increments on adjusting ring for fastening torque Fastening torque.
The necessary torque can be set by swiveling the adjusting ring (6) towards the relevant symbol.
Speed change lever o Adjusting ring p Graduations a Drill marking s Pointer d Limit mark f Screwdriver g Brush holder cap.
You'll also be interested in:
Examples of using Adjusting
Show more
Adjusting the balance effects all sources
Proceed as for adjusting the left fence
Adjusting the white balance manually recommended
Examples of using Ring
Show more
And place a ring upon her hand
Ring tones will not hold up in court
I had to go into the ring to finish it myself
