Examples of 'bending stresses' in a sentence
Meaning of "bending stresses"
Bending stresses refer to the internal forces or pressures exerted on an object when subjected to bending or flexing loads or moments
How to use "bending stresses" in a sentence
Basic
Advanced
bending stresses
Install without tension or bending stresses.
These bending stresses are highest at the root of the bristles.
Divisible module card which is resistant to bending stresses.
They limit the bending stresses and curvature to acceptable levels.
The cables obtained are resistant to crushing and to bending stresses.
These supports and guides prevent bending stresses on the chimney elbows and joints.
Avoid thread shaft in places experiencing alternating bending stresses.
The highest bending stresses are generated in regions R in the interconnecting portions proximate the corners.
This results in a decrease in allowable bending stresses at the connection region.
The bottom link is thus given particularly high resistance to bending stresses.
The twisting and bending stresses to which arbor 1 is subjected.
Such rigid connections undesirably give rise to localized bending stresses.
Cyclic stresses, in particular bending stresses and tension-compression stresses.
The connecting rod is subject to both torsional as well as flexural or bending stresses.
Since the value of the alternate bending stresses on the tubular component is,.
See also
The plasticity under bending is typically associated with local bending stresses.
Distribution of bending stresses is also an important factor in determining a stent 's susceptibility to fatigue.
The working pressure in fact causes bending stresses in the seal.
Thus, bending stresses over the opening and closing cycle may be reduced.
The neutral axis separates regions of tensile and compressive bending stresses.
Thus, the bending stresses are not influenced therein by prior stresses undergone by the sheet.
This choice is not prejudicial as regards resistance to the bending stresses of the card.
Loaded only by a moment, the peak bending stresses occurs at the outside fibers of a cross-section.
Another drawback of these cards is their mediocre ability to resist repeated bending stresses.
The block 31 is long enough to take up the bending stresses caused by heat shrinkage.
Completely impregnated continuous fibres give better results under tensile and bending stresses.
Twisting and bending stresses are equalized, thereby enabling the assembly to have good mechanical strength.
The inclination of the body of said inclinometer induces bending stresses on one piece.
Furthermore, bristles are subjected to bending stresses as brush 10 is rotated against a workpiece.
The first involves the differences in how the device behaves as bending stresses are applied.
If these locations are symmetrical, pure bending stresses are produced between the knives 30.
The notches have a generally sinusoidal shape that serves to distribute and minimize bending stresses.
This then enables the battery to undergo greater bending stresses and at a higher frequency.
Standard flexible corrugated metal arches 132 of Figure 17 are particularly weak in resisting bending stresses.
This reduction in thickness leads to a proportional decrease in bending stresses for a given horizontal displacement.
An ISO standard characterizes the resistance of the card to bending stresses.
The impact of tires moving over a pavement marker creates bending stresses and stress concentrations.
Moreover, perforations occasionally have some weakness in respect of bending stresses.
Furthermore, the wider track shoes have greater bending stresses induced in them.
Fit filter combination o Note flow direction o Install without tension or bending stresses 3.
This vibration can result in relatively large amplitude dependent bending stresses developing in the tubes.
Install rotatable connector piece o Note flow direction o Install without tension or bending stresses 3.
In contrast to boiler designs with stud bolts, inadmissible bending stresses are avoided.
Therefore, the stud bolts 58 experience both axial stresses and bending stresses.
Mainsprings usually broke at their attachment to the arbor, where bending stresses are greatest.
At the cross section of each individual conductor, however, bending stresses arise.
Moreover, misalignment of the neutral fibres also induces secondary bending stresses at the junction.
However, the Tetron structure is impractical due to large bending stresses on the struts.
You'll also be interested in:
Examples of using Bending
Show more
Steam bending is a traditional process steeped in history
Exceptional inverse bending test fatigue strength
Bending over in them tight little clamdiggers
Examples of using Stresses
Show more
Mitigating the stresses that drive change
Stresses the need for general disarmament
My life coach always stresses the importance
