Examples of 'clamp nut' in a sentence
Meaning of "clamp nut"
A 'clamp nut' refers to a type of fastening or securing device that is used to hold objects together by clamping them tightly in place
How to use "clamp nut" in a sentence
Basic
Advanced
clamp nut
Then tighten the clamp nut securely.
Tighten clamp nut securely with the wrench provided.
Depress spindle lock and rotate clamp nut until.
Tighten the clamp nut with a wrench.
Securing the gimbal assembly may comprise tightening a clamp nut.
Tighten the clamp nut with the proper wrench.
Depress the spindle lock button and tighten clamp nut with.
Install bar clamp nut and finger tighten only.
The grinder is shipped with the disc flange and clamp nut attached to the spindle.
Loosen clamp nut and insert bit into tool holder.
Loosen and remove the clamp nut from the spindle.
Turn the clamp nut clockwise to secure the handle in the desired.
Use the spanner provided as you tighten the clamp nut in a clockwise direction.
Loosen the clamp nut and widen the side handle base.
Depress and hold the spindle lock and rotate the clamp nut until the spindle locks.
See also
The flange and clamp nut must have same outer diameter.
S Loosen and remove bar clamp nut and.
Thread the clamp nut on the spindle with the flat side.
Fit the raised, small diameter portion of the clamp nut.
Just loosen the clamp nut to swing the side handle to a desired position.
To secure the side handle, tighten the clamp nut securely.
Tighten the threaded clamp nut ( e ) with the hex key provided or a two pin spanner.
Optionally, securing the gimbal assembly comprises tightening a clamp nut.
While lifting tip of guide bar, tighten bar clamp nut securely with the bar tool.
Install the threaded clamp nut with the raised section ( pilot ) facing away from the wheel.
While depressing the spindle lock button, tighten the clamp nut with a wrench.
Each clamp nut 5 is provided with a toothed crown 5a.
Then tighten the clamp nut securely . Fig.
Clamp the tool to the tool bracket by tightening the clamp nut PICTURE 3.
Tighten the threaded clamp nut 14 with the twopin spanner.
Install disc flange, grinding wheel, and clamp nut.
Ring on the threaded clamp nut 14 must face towards the rubber backing pad.
Reassemble disc flange, grinding wheel, and clamp nut.
Install the threaded clamp nut with the pilot facing away from the wheel . 4.
Depress the spindle lock button and tighten clamp nut with a wrench . 5.
Tighten the threaded clamp nut ( N ) with the two-pin spanner supplied.
While depressing the spindle lock button ( 6 ), tighten the threaded clamp nut with included wrench.
To remove the disc, loosen the threaded clamp nut ( h ) with the two-pin spanner.
A system 40 for screwing on or off the clamp nut 5.
To remove the rubber backing pad, loosen the threaded clamp nut ( 14 ) wih the two-pin spanner.
While depressing the spindle lock button, thread the clamp nut ( G ) on spindle.
While depressing the spindle lock button, thread the clamp nut ( H ) on spindle.
Figure L - While depressing the spindle lock button, thread the threaded clamp nut ( 8 ) on spindle.
You'll also be interested in:
Examples of using Nut
Show more
I am kind of a hard nut to crack in that department
A nut who knows a lot about bombs
Loosen the bottom nut to eliminate water
Examples of using Clamp
Show more
Do not subject the clamp to running water
You clamp the top of your throat
Then tighten the clamp screw securely
