Examples of 'knurled nut' in a sentence
Meaning of "knurled nut"
A knurled nut is a type of fastening hardware that has a pattern of ridges or small, shallow grooves (known as knurling) on its outer surface. These ridges provide additional grip and make it easier to tighten or loosen the nut by hand, without the need for tools. Knurled nuts are commonly used in applications where frequent adjustments or disassembly are required
How to use "knurled nut" in a sentence
Basic
Advanced
knurled nut
At the top there should be a knurled nut.
Turn the knurled nut towards the flash.
Fix the tare weight in position using the knurled nut.
Hold knurled nut until glows the catalyst.
Oven and undo the knurled nut at the front.
A knurled nut is a nut with a knurled outside surface.
The soldering iron bit is now loose in the knurled nut.
Screw the knurled nut of the adapter as far as.
Then screw on new tip by appropriately turning the knurled nut.
Unscrew the knurled nut of the solenoid coil.
The mandible support is displaceable vertically by means of a vertical screw and a knurled nut.
Push the knurled nut upward to open ignition holes.
The nose is retightened by turning the knurled nut in the opposite direction.
Note knurled nut holding in the replaceable front sight insert.
Replace the tip with another tip and screw the knurled nut barrel.
See also
Screw with knurled nut for cutting depth limi.
The locking force of the rip fence can be set with the rear knurled nut.
Thin knurled nut.
Simple direct mounting Straightforward direct mounting on the valve with only one knurled nut.
High knurled nut.
Knurled nut Gas control lever.
Loosen and remove tip by turning the knurled nut to right and mount a hotblow tip.
Back up knurled nut and put a few drops of machine oil on packing.
Aerial in operating position ; knurled nut.
Firmly tighten the knurled nut against the resistance of the rubber ring.
To replace the fuse, unscrew the knurled nut.
Turn the knurled nut towards the flash unit housing as far as it will go.
Align the camera coarsely and fix it by tightening the lower knurled nut 8.
Remove the knurled nut and lift the drum from the clock.
Check connecting line and fasten plug-in connector by tightening the knurled nut.
Turn the knurled nut against the mecablitz until the stop point is reached.
To remove rack guides, unscrew the knurled nut on the front of the rack guide.
Turn the knurled nut all the way downwards against the flash shoe of the.
Caution, The soldering tip and the knurled nut are hot.
Screw the plastic knurled nut onto the threaded rod of the wall bracket.
Remedy, Check connecting line and fasten plug-in connector by tightening the knurled nut.
Turn knurled nut 4 until its front is flush with the bolt.
To do this loosen the knurled nut on the screw 26.
Turn the knurled nut towards the camera housing as far as it will go, clam.
Return using the knurled nut 9.
Nylon knurled nut acts as jam nut to fix the position of the fine-adjustment screw.
A nut, for example of the knurled nut type, can be used as a stop.
The knurled nut ( 2 ) must stay at its position against the stopper.
For this, completely unscrew the knurled nut 8 and then pull out the hexagon bolt upward.
Knurled nut size 2, also suitable for pipe wrenches size 3.
Secure this setting with the knurled nut ( A ) which simultaneously fastens the upper arm cover.
The adjusting ring ( 3 ) can no longer be turned over the knurled nut 2.
Completely unscrew the knurled nut 4 and then pull out the hexagon bolt upward.
Turn the adjusting ring ( 3 ) in the opposite direction of the knurled nut 2.
Tension lower, Turn the knurled nut 2 counterclockwise.
You'll also be interested in:
Examples of using Nut
Show more
I am kind of a hard nut to crack in that department
A nut who knows a lot about bombs
Loosen the bottom nut to eliminate water
Examples of using Knurled
Show more
Knurled clamp area for optimal stability
After loosening the two knurled nuts
Turn the knurled nuts on the base of
