Examples of 'loosen screw' in a sentence
Meaning of "loosen screw"
Loosening a screw refers to the action of turning or rotating it in a counterclockwise direction to reduce the tightness or tension between the screw and the material it is secured in. This is typically done using a screwdriver or another appropriate tool. Loosening a screw is often necessary when adjusting or removing components, performing maintenance, or disassembling objects that are held together by screws
How to use "loosen screw" in a sentence
Basic
Advanced
loosen screw
This will loosen screw inside chuck.
Lay shade poles on the table and loosen screw.
Loosen screw and tilt cover to re move.
Insert screwdriver through bottom louver in grille and loosen screw while.
Loosen screw on venturi and adjust as necessary.
To replace batteries, loosen screw and remove battery door.
Loosen screw at least three full turns.
If adjustment is necessary, loosen screw on quadrant plate and adjust as necessary.
Loosen screw and slide hinge apart.
To open the battery compartment, loosen screw and remove battery lid.
Loosen screw to increase the flame height.
Proceed as follows, - Loosen screw located on lower side.
Loosen screw and tilt cover to remove.
Aligning the pedal - Loosen screw on the rod 2.
Loosen screw and washer on freezer side wall.
See also
It is sufficient to operate the tongue 42 in order to tighten and loosen screw 41.
Loosen screw and turn shutter.
Frist with engine off, loosen screw A 1.
Loosen screw the screw remains captive on wallplate.
To uninstall, loosen screw and remove belt clip.
Loosen screw terminals used for the application.
To readjust, loosen screw and set the appropriate interval.
Loosen screw holding belt tension spring to transmission.
Use a screwdriver to loosen screw terminals, wrap bare wire securely around terminals, then tighten screws.
Loosen screw with keyhole opening.
Use a screwdriver to loosen screw terminals, insert wires, then tighten screws.
Loosen screw on carrier arm head and remove casing.
To readjust, loosen screw ( 1 ) and set the appro priate interval.
Loosen screw in rear plate that secures recovery tank to.
ENGLISH 14 - loosen screw to increase the flame height.
Loosen screw on battery retention bracket and rotate aside.
Using a screwdriver, loosen screw C by turning it clockwise to increase the hydraulic compression damper.
Loosen screw and remove the air cleaner cover.
Tighten or loosen screw 31 and rotate knob 32 clockwise until it smoothly penetrates to abutment.
Loosen screw plug inside pressure tap located on underside of valve.
Adjusting, - Loosen screw 56 using a Phillips screwdriver and align the.
Loosen screw holding exterior wiring compartment cover and remove cover.
Loosen screw r and then move the needle bar q up or down to adjust its position.
Loosen screw C of the lamp socket and.
Loosen screw A and open the cover.
Loosen screw R and remove toothed belt cover.
Loosen screw Adjust air shutter opening Tighten screw.
Loosen screw in the stopper, and move stopper.
Loosen screw 0 in the bobbin case opening lever and adjust.
Loosen screw located in the center of hex knob approximately 3 turns.
Loosen screw 18 clockwise with the tubular key as delivered together with the equipment.
Loosen screw A on the bicycle rack ( hereinafter only referred to as carrier ) in.
Loosen screw E1 in the clockwise direction.
Loosen screw ( b ) ready for setting the splitting wedge.
Loosen screw terminals, insert wires into terminal block, then re-tighten screws.
