Examples of 'loosen the nut' in a sentence
Meaning of "loosen the nut"
loosen the nut: Refers to the action of making a nut less tight, usually by turning it counterclockwise, to detach or adjust a mechanical component
How to use "loosen the nut" in a sentence
Basic
Advanced
loosen the nut
Loosen the nut by means of the spanner.
Time to find and loosen the nut.
Loosen the nut and locknut on the transmission.
Both of us were unable to loosen the nut.
We loosen the nut under here.
Tools are required to loosen the nut and screws.
Just loosen the nut to swivel the handle freely.
If any adjustment is needed loosen the nut first.
Loosen the nut until you hear a hissing noise.
You may need to use the wrench to loosen the nut.
Loosen the nut and remove the clutch cover.
Then make it about a quarter turn counterclockwise to loosen the nut lightly.
Loosen the nut on the coil and remove coil.
Place the wrench over the fitting and loosen the nut.
We have to loosen the nut and remove the pin.
See also
The crown shape of the nut prevents the use of a chisel to loosen the nut.
Loosen the nut sufficiently to allow the wheel to turn freely.
If necessary, use a wrench or screwdriver to loosen the nut.
Loosen the nut u and move the roller shaft up or down to adjust.
Using the same procedure, loosen the nut a second time.
Loosen the nut and washers on the four corners of the fan.
Open the quick-release lever and loosen the nut.
Loosen the nut and swing the side handle to the desired position.
Fully tighten the locknut, then loosen the nut two full turns.
Loosen the nut at the base of the leveler to allow the leveler to rotate.
To adjust the wheel correctly, loosen the nut that fixes the wheel to the chassis.
Loosen the nut that secures the ball of the pump into the mounting socket.
On the underside of the saw, loosen the nut II.
Using a suitable spanner loosen the nut sufficiently to allow adjustment of the shaft bm.
To tighten the chain, loosen the nut.
Use pliers to loosen the nut on the front of the cigarette lighter adapter slightly.
If an adjustment is required, loosen the nut 9.
Loosen the nut on the outlet tube and move the outlet tube to the side.
To adjust, tighten or loosen the nut D.
Loosen the nut and the ring from the capacitor till the end from the thread.
Note, hold the crankshaft by UNIVERSAL ROTOR HOLDER to loosen the nut 1.
Nut Loosen the nut on the threaded rod and.
Use the included wrench to loosen the nut ( G ) from the drive shaft H.
Loosen the nut while holding the bolt with an Allen wrench.
If not, adjust the chain as follows, - loosen the nut.
Loosen the nut on the DHW outlet pipe at the bottom of the storage boiler.
A torque is applied on the tool 54 in the direction to loosen the nut 38.
Loosen the nut on the cover of the EMI board and slide the cover back.
Rotate ' Clockwise ' to loosen the nut only.
Loosen the nut and take out the connection screw from the FCS board mount.
No, no, no, no . We have to loosen the nut and remove the pin.
Loosen the nut on the squaring tool, and.
Then make it about a quarter turn counterclockwise to loosen the nut lightly . Fig . 11.
Loosen the nut by placing the open-ended spanner.
Hold the disc ( A ) with one spanner and loosen the nut ( B ) with the other spanner.
You'll also be interested in:
Examples of using Nut
Show more
I am kind of a hard nut to crack in that department
A nut who knows a lot about bombs
Loosen the bottom nut to eliminate water
Examples of using Loosen
Show more
Loosen the screw at the rod extensions
Use a screwdriver to loosen the air shutter
Loosen the lower pin with a key
