Examples of 'sanding plate' in a sentence
Meaning of "sanding plate"
sanding plate: A tool used for smoothing or leveling surfaces by sanding
How to use "sanding plate" in a sentence
Basic
Advanced
sanding plate
Press the sandpaper to the sanding plate.
That holes in sanding plate and paper correspond.
Dust extractor holes on sanding paper and sanding plate.
Clean the sanding plate before you attach a sanding sheet.
The washer is not required to mount the sanding plate.
The specialty sanding plate is attached in the same manner as the one supplied.
Pull sanding disc tightly over the sanding plate.
The hole pattern in the sanding plate and sanding sheet must match.
Press the sanding sheet firmly against the sanding plate.
The sanding plate can be fastened onto the drive shaft in any position.
The sanding sheets are placed directly onto the sanding plate.
The sanding plate is fitted with a hook and eye system for sanding sheets.
Align the sanding sheet and press it onto the sanding plate.
Replacing the Sanding Plate see figure.
Possible to work only with the tip or an edge of the sanding plate.
See also
Replace a damaged sanding plate 5 immediately.
Only attach accessories with hook and eye coatings to the sanding plate.
The sanding plate is provided with a velcro-type fasten for.
Align the sanding sheet and press it onto the sanding plate by hand.
Guide the sanding plate 5 from below against the sand.
If necessary attach the upper foam pad above the upper side of the sanding plate.
Pull the rear sanding plate 8 by the recessed grips down.
SDS button for release of the sanding plate.
Attach the new sanding plate 5 and tighten the screw again.
You can attach the sanding sheet to the sanding plate using the Velcro.
Attach the new sanding plate 9 and tighten the screws again.
Clean the upper side of the new sanding plate 4.
As a result of the forced drive, the sanding plate has constant eccentricity and rotational movement.
Fold the sanding sheet 6 firmly around the sanding plate.
Due to its plane sanding plate surface, optimum results are achieved, especially for finish sanding.
The adapter 4 is required for working with the sanding plate.
The operation of the speciality sanding plates is only permitted with a mounted rear sanding plate 8.
Make sure that the sanding sheet 9 lies taught on the sanding plate.
Press the sanding plate 8 onto the holder until you hear it click into place.
When attaching a new sanding sheet, remove any dust or debris from the sanding plate 4.
The supplied sanding plate 4 is fitted with Velcro backing and can be replaced.
Before placing on a new sanding sheet, free the sanding plate from dust and dirt.
Quick sanding disc change Sanding plate suitable for sanding discs with and without velcro-type fastening.
Before fitting a new sanding sheet, remove any dust and dirt from the sanding plate.
Wide variety of applications Triangular sanding plate for sanding corners, edges and surfaces.
A Sanding plate ( as replacement ) B Dust collection box with fluted filter for multiple.
Slide the SDS button for release of the sanding plate 6 all.
The sanding plate 9 can be replaced, if required.
Removing the two-part sanding plate see figure D.
Completely unscrew the screw 6 and take off the sanding plate 5.
Pull it tightly over the sanding plate ( 1 ) and clamp to the other clamping element.
Unscrew the four screws 8 completely and remove the sanding plate 4.
Attaching the two-part sanding plate see figure E.
Press the sanding sheet 10 firmly against the bottom side of the sanding plate 8.
The delta sanding plate ( 30 ) is fitted with Velcro for rapid attachment of the sanding sheet.
You'll also be interested in:
Examples of using Plate
Show more
Put the upper plate on the stove
Face plate in position for shredding paper
Do not submerge hot plate or burners in water
Examples of using Sanding
Show more
Sanding sheets are available in a variety of different grades
Recoatable without sanding of the previous layer
Sanding discs are available in a variety of different grades
